FBO Notice Date 12/14/17
BIDS Reference Number 860
Document Type: Amendment
Hardware & Abrasives

Defense Logistics Agency, DLA Acquisition Locations, DLA Troop Support - Industrial Hardware, 19111-5096

53 -- Locking Plate, Nut and Bolt SOL SPE5EC17R0004COMBINE DUE 122217 POC Carlos A. Lopez, Phone 2157378343, Email carlos.lopez@dla.mil - Kimberly J. DiBartolomeo, Contracting Officer, Phone 215-737-9244, Email kimberly.dibartolomeo@dla.milSolicitation is hereby extended until December 22, 2017 3:00 pm EST

LOCKING PLATE, NUT AND BOLT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR
SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE
SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE
ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE
APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON
REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)


RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT


RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)


RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN


RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

THIS IS A NAVY IDENTIFIED CRITICAL SAFETY ITEM
(CSI).

ALL REQUESTS FOR WAIVERS OR DEVIATIONS MUST BE
FORWARDED TO THE DSC CONTRACTING OFFICER FOR
REVIEW AND APPROVAL.
.
ALL ITEMS OF SUPPLY SHALL BE MARKED IAW
MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL
BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE),
CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S
CAGE CODE AND PART NUMBER.
UNLESS OTHERWISE NOTED
FIRST ARTICLE TESTING IS REQUIRED
THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO
EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND
ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH
JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF
STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL
AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY CRITICAL
TECHNICAL DATA AGREEMENT, FORM IS AVAILABLE AT THE WORLD WIDE WEB
ADDRESS:

https://public.logisticsinformationservice.dla.mil/PublicHome/jcp/defaul
t.aspx

OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE
FEDERAL CENTER
74 WASHINGTON AVE., NORTH
BATTLE CREEK, MI 49037-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A
CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,
DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY
THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN
EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF
GENERAL APPLICABILITY, AND/OR EAR PART 740 ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE
REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT
OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE
EXPORT CONTROLLED TECHNICAL DATA.

NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO
THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA
UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY
PERMITTED BY DODD 5230.25.

MIL-STD-130N, 16 Nov 2012
IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
DATA IS PROPRIETARY OR INSUFFICIENT FOR
COMPETITIVE PROCUREMENT

THE ACCEPTABLE SOURCE(S) MUST MEET THE REQUIREMENTS
OF THE CURRENT REVISION OF THE OEM DRAWING

OFFERORS NOT CITED AS ACCEPTABLE SOURCES IN THE
PROCUREMENT ITEM DESCRIPTION ARE REQUIRED TO
OBTAIN SOURCE APPROVAL FROM THE DESIGN CONTROL
ACTIVITY. SOURCE APPROVAL REQUESTS/TECHNICAL
DATA PACKAGES MUST BE SUBMITTED TO DLA WITH
THE OFFER.

CRITICAL ITEM - SOURCE INSPECTION REQUIRED.
ALERT -- ALL SAFETY CRITICAL PARTS TO BE PACKAGED QUP OF 001. EACH UNIT
PACKAGE WILL BE MARKED WITH THE NSN, CONTRACT
NUMBER, LOT NUMBER, CONTRACTOR CAGE CODE, MANUFACTURER'S CAGE CODE AND
PART NUMBER.
QAP EQ003 APPLIES


COMPLETE FIRST ARTICLE TEST (FAT) AND PRODUCTION LOT TEST (PLT) REPORTS
SHALL BE SENT TO: DLAHardwareFATMonitor@DLA.MIL

PLT SAMPLE SIZE PER TABLE 1 OF QAP-CSI011521100

CRITICAL APPLICATION ITEM

MAGELLAN AEROSPACE, NEW YORK, INC. 85941 P/N 74A410714-2003
AEROMETALS,INC. 32664 P/N 74A410714-2003
NASSAU TOOL WORKS, INC. 2M490 P/N 74A410714-2003
SAFRAN LANDING SYSTEMS CANADA INC 35962 P/N 74A410714-2003
BOEINGCOMPANY, THE DBA BOEING 76301 P/N 74A410714-2003
HDI LANDING GEAR USA, INC. DBA 5ZSC8 P/N 74A410714-2003
ISRAEL AEROSPACE INDUSTRIES LTD. 1935A P/N 74A410714-2003
AJ FLORIDA (AJ ASSOCIATES MFG. & ENG. CO., INC.) (3Z260)P/N 74A410714-2003

IAW REFERENCE DRAWING NR 76301 74A410714
REVISION NR C DTD 09/21/2006
PART PIECE NUMBER: 74A410714-2003

IAW REFERENCE DRAWING NR 76301 PL74A410714
REVISION NR C DTD 11/03/1998
PART PIECE NUMBER: 74A410714-2003

IAW REFERENCE QAP 14153 QAP-EQ003
REVISION NR B DTD 05/16/2013
PART PIECE NUMBER:

IAW REFERENCE QAP 14153 QAP-CSI011521100
REVISION NR A DTD 04/05/2016
PART PIECE NUMBER:

CITE: https://www.fbo.gov/notices/1b9439b1b488654ce2d4d36d9da0fb71

SET-ASIDE: Total Small Business